Introduction
The MGate 5103 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP, EtherNet/IP, and PROFINET network communications. To integrate existing Modbus devices onto a PROFINET network, use the MGate 5103 as a Modbus master/slave or EtherNet/IP adapter to collect data and exchange data with PROFINET devices. The latest exchange data will be stored in the gateway. The gateway will convert stored Modbus or EtherNet/IP data into PROFINET packets so the PROFINET IO Controller can control or monitor field devices.
Easy Configuration via Web Console The MGate 5103 Series comes with an illustrated Quick Setup guide designed to make configuration easy. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps. The MGate 5103 Series also supports a GSDML export function. GSDML files can be imported into PROFINET PLCs to save time on PLC configuration. Modbus RTU/ASCII/TCP Protocol Traffic Monitor MGate 5103 gateways support Modbus RTU/ASCII/TCP Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave IDs and register addresses, that were entered incorrectly, or an incorrect command configuration. With Modbus RTU/ASCII/TCP Protocol Traffic Monitor, you can check the captured data and easily identify the root cause. Maintenance Functions MGate 5103 gateways support a system log function that records events in the MGate; users can easily review log data remotely through the web console. The gateways also support status monitoring and fault protection functions. The status monitoring function notifies a PLC/DCS/SCADA system when a Modbus device gets disconnected or does not respond, in which case the process PLC/DCS gets the status of each end device and then issues alarms to notify operators.
Documentation
Data Sheet PDF Quick Start Guide PDF User Manual
Memory
microSD Slot
Up to 32 GB (SD 2.0 compatible)
Relays
Contact Current Rating
Resistive load: 2 A @ 30 VDC
Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector)
2
Magnetic Isolation Protection
Ethernet Software Features
Industrial Protocols
EtherNet/IP Adapter (Slave), Modbus TCP Client (Master), Modbus TCP Server (Slave), PROFINET IO Device (Slave)
Configuration Options
Device Search Utility (DSU), Web Console, Telnet Console
Management
ARP, DHCP Client, DNS, HTTP, HTTPS, SMTP, SNMP Trap, SNMPv1/v2c/v3, TCP/IP, Telnet, SSH, UDP
MIB
Time Management
Serial Interface
Console Port
RS-232 (TxD, RxD, GND), 8-pin RJ45 (115200, n, 8, 1)
Baudrate
Connector
Data Bits
Flow Control
RTS Toggle (RS-232 only), RTS/CTS
No. of Ports
Parity
None, Even, Odd, Space, Mark
RS-485 Data Direction Control
ADDC® (automatic data direction control)
Serial Standards
Stop Bits
Pull High/Low Resistor for RS-485
1 kilo-ohm, 150 kilo-ohms
Terminator for RS-485
Isolation
Serial Signals
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422
RS-485-2w
RS-485-4w
Serial Software Features
Configuration Options
Industrial Protocols
Modbus RTU/ASCII Master, Modbus RTU/ASCII Slave
Modbus RTU/ASCII
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
Input Data Size
Max. No. of Commands
Mode
Output Data Size
Modbus TCP
Functions Supported
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Client Connections
Max. No. of Commands
Max. No. of Server Connections
Input Data Size
Mode
Output Data Size
PROFINET
Input Data Size
Max. No. of IO Controller Connections
Mode
Output Data Size
EtherNet/IP
CIP Objects Supported
Identity, Message Router, Assembly, Connection Manager, TCP/IP interface, Ethernet link, Port
Input Data Size
Max. No. of Scanner Connections
1 (for read-only), 1 (for read/write)
Mode
Output Data Size
Power Parameters
Input Current
Input Voltage
Power Connector
Screw-fastened Euroblock terminal
Physical Characteristics
Housing
IP Rating
Dimensions
36 x 105 x 140 mm (1.42 x 4.14 x 5.51 in)
Weight
Environmental Limits
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Storage Temperature (package included)
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% (non-condensing)
Standards and Certifications
Safety
EMC
EMI
CISPR 32, FCC Part 15B Class B
EMS
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
Hazardous Locations
ATEX, Class I Division 2, IECEx
Freefall
Shock
Vibration
IEC 60068-2-6
Features
Protocol conversion between Modbus, EtherNet/IP, and PROFINET
Supports PROFINET IO device Supports Modbus RTU/ASCII/TCP master/client and slave/server Supports EtherNet/IP Adapter Effortless configuration via web-based wizard Built-in Ethernet cascading for easy wiring Embedded traffic monitoring/diagnostic information for easy troubleshooting microSD card for configuration backup/duplication and event logs Status monitoring and fault protection for easy maintenance Serial port with 2 kV isolation protection -40 to 75°C wide operating temperature models available Supports redundant dual DC power inputs and 1 relay output Security features based on IEC 62443
