|
|
|
|
Network Readiness for up to Four Serial Devices The NPort® 5410 device server can conveniently and transparently connect up to four serial devices to an Ethernet, allowing you to network your existing serial devices with only basic configuration. Data transmission between the serial and Ethernet interfaces is bi-directional. By using NPort® device servers, you not only protect your current hardware investment, but also allow for future network expansion. You can both centralize the management of your serial devices, and distribute management hosts over the network.
Independent Operation Mode for each Serial PortThe NPort 5410 device server can be used to connect different devices for remote data polling, event handling, or data multicasting over a TCP/IP network. Each serial port on the NPort 5410 operates independently to provide maximum versatility. For example, port 1 can operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4 in TCP Client mode. User-friendly LCD Panel for Easy Installation An LCD panel is built into the NPort® 5400’s top panel, with four buttons for inputting data, configuration, and selecting the operation mode. The LCD panel displays the server name, serial number, and IP address, and can be used to enter or modify parameters such as IP address, netmask, and gateway.
Redundant DC Power Inputs NPort® 5400 device servers support redundant power sources and provide both a DC terminal block input and a DC power jack input. The two power inputs not only provide power redundancy, but also allow greater flexibility for use with different applications.
Adjustable Termination and pull High/Low Resistors Termination resistors may be needed in some critical environments to prevent the reflection of serial signals. When using termination resistors, it is important to set the pull high/low resistors correctly to prevent the electrical signal from being corrupted. Since no set of resistor values is universally compatible with all environments, the NPort® 5400 has four sets of DIP switches on the bottom panel to set the termination and pull high/low resistor values.
Ethernet Interface
|
Number of Ports
|
1
|
Speed
|
10/100 Mbps, auto MDI/MDIX
|
Connector
|
8-pin RJ45
|
Magnetic Isolation Protection
|
1.5 kV built-in
|
• Serial Interface
|
Number of Ports
|
4
|
Serial Standards
|
NPort 5410: RS-232
NPort 5430/5430I: RS-422/485 (software selectable) NPort 5450/5450I/5450-T/5450I-T: RS-232/422/485 (software selectable)
|
Connector
|
NPort 5410/5450/5450I/5450-T/5450I-T: DB9 male
NPort 5430/5430I: Terminal block
|
Serial Line Protection
|
2 kV isolation protection (NPort 5430I/5450I/5450I-T)
|
RS-485 Data Direction Control
|
ADDC® (Automatic Data Direction Control)
|
Pull High/Low Resistor for RS-485
|
1 kΩ, 150 kΩ
|
Terminator for RS-485
|
120 Ω
|
• Serial Communication Parameters
|
Data Bits
|
5, 6, 7, 8
|
Stop Bits
|
1, 1.5, 2
|
Parity
|
None, Even, Odd, Space, Mark
|
Flow Control
|
RTS/CTS and DTR/DSR (RS-232 only), XON/XOFF
|
Baudrate
|
50 bps to 921.6 kbps
|
• Serial Signals
|
RS-232
|
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
|
RS-422
|
Tx+, Tx-, Rx+, Rx-, GND
|
RS-485-4w
|
Tx+, Tx-, Rx+, Rx-, GND
|
RS-485-2w
|
Data+, Data-, GND
|
• Software
|
Network Protocols
|
ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1, HTTP, SMTP, SNTP, Rtelnet, ARP
|
Configuration Options
|
Web Console, Telnet Console, Windows Utility
|
Windows Real COM Drivers
|
Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded
|
Fixed TTY Drivers
|
SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
|
Linux Real TTY Drivers
|
Linux 2.4.x, 2.6.x, 3.x
|
• Mini Screen with Push Buttons (for standard temp. models)
|
LCD Panel
|
Liquid Crystal Display on the case
|
Push Buttons
|
Four push buttons for convenient on-site configuration
|
• Physical Characteristics
|
Housing
|
Metal
|
Weight
|
740 g (1.63 lb)
|
Dimensions
|
Without mounting kit: 158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 181 x 103 x 33 mm (7.14 x 4.06 x 1.30 in)
|
• Environmental Limits
|
Operating Temperature
|
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
|
Storage Temperature
|
-40 to 75°C (-40 to 167°F)
|
Ambient Relative Humidity
|
5 to 95% (non-condensing)
|
• Power Requirements
|
Input Voltage
|
12 to 48 VDC
|
Input Current
|
NPort 5410: 350 mA @ 12 VDC
NPort 5430: 320 mA @ 12 VDC NPort 5430I: 530 mA @ 12 VDC NPort 5450/5450-T: 350 mA @ 12 VDC NPort 5450I/5450I-T: 554 mA @ 12 VDC
|
• Standards and Certifications
|
Safety
|
UL 60950-1
|
EMC
|
EN 55022/24
|
EMI
|
CISPR 22, FCC Part 15B Class A
|
EMS
|
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m IEC 61000-4-8 PFMF IEC 61000-4-11 DIPs
|
Marine
|
DNV (standard temp. models only)
|
Medical
|
EN 60601-1-2 Class B, EN 55011 (NPort 5410/5450/5450I only)
|
• Reliability
|
Alert Tools
|
Built-in buzzer and RTC (real-time clock)
|
Automatic Reboot Trigger
|
Built-in WDT (watchdog timer)
|
• MTBF (mean time between failures)
|
Time
|
NPort 5410: 310,331 hrs
NPort 5430/5430I: 265,650 hrs NPort 5450/5450I: 206,903 hrs
|
Standard
|
Telcordia (Bellcore) Standard TR/SR
|
• Warranty
|
Warranty Period
|
5 years
|
Details
|
See www.moxa.com/warranty
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features
- 10/100M auto-sensing Ethernet
- 4 serial ports, with support for RS-232, RS-422, and RS-485
- Built-in 15 KV ESD surge protection for all serial signals
- Versatile socket operation modes, including TCP Server, TCP Client, UDP, and Real COM
- Choice of configuration methods: Web console, Telnet console, and Windows utility
- SNMP MIB-II for network management
- 2 KV isolation protection for NPort 5430I/5450I/5450I-T
- -40 to 75°C operating temperature range (T model)
|
|
|
|
|
|
|